Gromtech Effects
Gromtech Dynamic Bass Amp 7400 plugin interface, a recreation of the Marshall DBS 7400

Bass preamp plugin

Gromtech Dynamic Bass Amp 7400Marshall DBS 7400* recreation

A 1990s British bass head's valve and solid-state front end, faithfully recreated as a plugin.

The first plugin recreation of the Marshall DBS 7400.

One licence for Windows and Mac. Both installers are on the download page after you buy.

Windows 10/11 and macOS 11+ · VST3, CLAP and Audio Unit · One licence for both · Works offline

Hear it A/B tested against the original Marshall DBS 7400:

A faithful recreation of the front end of the Marshall DBS 7400*, the British bass head of the 1990s: a solid-state channel and a valve channel that blend into each other, tone controls, a compressor and a nine-band graphic equaliser.

Or get all 4 of our plugins for US$97, 20% less than buying them separately. See the bundle

A faithful recreation of the Marshall DBS 7400

Gromtech Dynamic Bass Amp 7400 was built with a physical Marshall DBS 7400 on the bench. We inspected it, measured it, and compared the plugin against it meticulously: the gain, the valve, the tone controls, the compressor and every slider of the graphic, across their settings.

The result responds the way the amplifier does wherever you set it, from clean and solid to a valve growl.

This is the amplifier up to its D.I. output. There is no power amplifier or loudspeaker in it, so use it as it is for a direct bass sound, or follow it with a cabinet simulation.

The Marshall amps in Muse's bass rig

In a Dunlop TV interview, Shane Goodwin, then Muse's bass tech, walked through the rack behind Chris Wolstenholme's sound: three amps, each fed by its own signal path. Asked about the Marshalls in the rack, he explained:

“Basically they're Marshall DBS, Dynamic Bass System. They don't make them anymore.”

In the footage the heads are labelled by path: “1. Clean”, “2. Big Muff” and “3. Animato”. The rig list in Chris's 2009 interview names the model: a Marshall DBS 7400 on each of the three rigs.

Rich Costey, who worked on Absolution and Black Holes and Revelations with the band, told EQ in 2007 how Chris kept coming back to them: “He brought in about five or six different amps to try out, and we ended up right back where we started. They're basically these Marshall bass heads that nobody else has.”

Gromtech Dynamic Bass Amp 7400 recreates the preamp of the DBS 7400, and pairs with Aminato and Eastern Black Fuzz in your session. Run three copies side by side, one clean, one after the Big Muff and one after the Animato, to set up the same split.

Sources: Dunlop TV, “Muse Bass Tech, Shane Goodwin”, published in 2010 and written up by Effects Bay; Chris Wolstenholme's 2009 interview with Bryan Beller, republished by Guitar World; Rich Costey in EQ, March 2007. Gromtech Dynamic Bass Amp 7400 is not affiliated with, sponsored by or endorsed by Muse, Chris Wolstenholme, Rich Costey, Shane Goodwin or Dunlop.

Controls

GAIN
How hard the two channels are driven, from clean to a valve growl.
PRE-AMP BLEND
Solid state to the left, valve to the right, and any mix of the two between.
BRIGHT and DEEP
Push-buttons for more top and more bottom.
LO and HI
Bass and treble, 15 dB either way.
COMPRESSION
Switch it in and set the depth: it takes more off the loud notes as it is turned up.
GRAPHIC EQUALIZER
Nine sliders from 50 Hz to 8 kHz, with a level control to make up for what they add or take away.
VOLUME
Output level.
INPUT
HI for passive basses. LO for active basses or a hot signal. A PEAK light shows when the amp is being pushed.
Power switch
Bypass.

Details

  • Windows 10 and 11, 64-bit
  • macOS 11 or later, Apple silicon and Intel
  • VST3 and CLAP, and Audio Unit on Mac
  • Any sample rate

Your licence

Buy a key, paste it into the plugin once, and it is unlocked for good. It works offline and there is no account to create.

Questions

What is Gromtech Dynamic Bass Amp 7400?

A bass preamp plugin that recreates the front end of the Marshall DBS 7400, the British valve and solid-state bass head, with its tone controls, compressor and graphic equaliser.

Is it an official Marshall plugin?

No. It is an independent recreation of the Marshall DBS 7400 made by Gromtech Effects, which is not affiliated with, sponsored by or endorsed by Marshall.

How close is it to the Marshall DBS 7400?

It was built by inspecting a physical amplifier and comparing the plugin against it across its controls, for maximum accuracy. Each control behaves as the hardware's does.

Does it include a cabinet?

No. It is the amplifier up to its D.I. output, which is how such an amp is usually recorded. Add a cabinet simulation or impulse response after it if you want one.

My active bass distorts it. What should I do?

Click the LO input socket, as you would plug into the low input of the amp. If the PEAK light is still on most of the time, turn GAIN down.

Which hosts does it work in?

Any 64-bit host on Windows or Mac. Reaper, Ableton Live, Cubase, Studio One, FL Studio and Bitwig all load it as VST3 on both systems. On a Mac it is also an Audio Unit, for Logic Pro, GarageBand and other hosts that use Audio Units. The installer puts every format in place.

Is there a Mac version?

Yes. It runs on macOS 11 or later, on Apple silicon and Intel Macs, as an Audio Unit, VST3 and CLAP. One licence key unlocks it on both Windows and Mac.

Does the licence need an internet connection or an account?

No. The key is checked on your own computer, the plugin never connects to the internet, and there is no account to create.

Get Gromtech Dynamic Bass Amp 7400

One licence for Windows and Mac. Both installers are on the download page after you buy.

Or get all 4 of our plugins for US$97, 20% less than buying them separately. See the bundle

* Gromtech Dynamic Bass Amp 7400 is not affiliated with, sponsored by or endorsed by the maker of the Marshall DBS 7400. The name is used solely to identify the hardware that this plugin recreates.

Gromtech Dynamic Bass Amp 7400 · US$49Buy